PhD With Me 🔬

nanojet settings maN-405

The most relevant paper for your specific request is J. Vac. Sci. Technol. B 26(5), Sep/Oct 2008 ("Large areas of periodic nanoholes perforated...") because it explicitly uses MaN-405 as a negative photoresist to create nanopillars. Here's a straightforward experimental approach based primarily on that paper, supplemented by general principles from the others: Understanding MaN-405 (Negative Photoresist in SLP): Negative Resist: MaN-405 hardens (polymerizes) where it is exposed to sufficient UV light. The unexposed areas are then washed away during development. Goal (usually with negative resist in SLP): To create pillars or posts where the light was focused by the microspheres. Key Finding (JVSTB 2008): Development time is critical. Too little leaves residue, too much destroys the features (pillars fall down). Developer choice (AZ-300 MIF vs. ma-D 331S) affects the pillar's sidewall profile (undercut vs. vertical). Experimental Protocol for In-House Optimization: Assumptions: You have a method to create a reasonably uniform monolayer of microspheres (your chosen size) on your MaN-405 coated substrate. You have a UV exposure tool (like a mask aligner) with a relatively collimated beam, likely centered around the g-line (436nm) or h-line (405nm) or i-line (365nm) based on typical negative resists, although the paper used 400nm broadband. You are aiming to create nanopillars. You have access to SEM for characterizing results. Steps: Establish Baseline: Start with the parameters closest to those mentioned in the JVSTB 2008 paper or your current best process: Photoresist: MaN-405 (Thickness matters, but keep it constant initially). Microspheres: Use your chosen diameter (e.g., the 0.97 μm silica spheres from the paper). Ensure good monolayer coverage. UV Exposure: Use your available UV source. Start with a fixed exposure dose (Intensity x Time). A good starting point might be similar to other papers if the JVSTB one isn't detailed enough on this for MaN-405 (many use exposure times from <1s to ~20s depending on intensity and resist). Pick one initial exposure time. Developer: Choose one developer to start with (e.g., AZ-300 MIF if you want undercut, or ma-D 331S if you want vertical walls, as per the paper. If using a different one, note it down). Initial Development Time: Start with a reasonable guess, perhaps around 30-60 seconds based on the paper's findings (Figure 3 showed results from 30s to 60s). Optimize Development Time (Most Critical First): Keep the UV exposure time constant. Prepare several identical samples. Develop each sample for a different amount of time. Create a time series, e.g., 20s, 30s, 40s, 50s, 60s, 70s. (Bracket the expected optimal time based on the JVSTB paper's ~50s finding with AZ-300 MIF). Characterize the results with SEM. Look for: Under-development: Unwanted resist residue between pillars, poorly defined shapes (like Figure 3a in JVSTB 2008). Optimal development: Cleanly defined pillars, no residue, pillars firmly attached (like Figure 3c in JVSTB 2008). Over-development: Pillars detaching, collapsing, or significantly thinner at the base than expected (like Figure 3d in JVSTB 2008). Identify the development time that gives the best-defined, cleanest, and most robust structures. This is your optimal development time for that specific exposure dose. Optimize UV Exposure Time (Control Feature Size): Use the optimal development time found in Step 2. Keep the developer constant. Prepare several identical samples. Expose each sample for a different amount of time. Create a time series, e.g., if your initial time was 10s, try 5s, 8s, 10s, 12s, 15s, 20s. (Supported by multiple papers showing feature size depends on exposure). Characterize the results with SEM. Look for: Pillar Diameter: How does the width of the pillar change with exposure time? (Expect larger exposure = larger diameter for negative resist). Pillar Robustness: Are pillars formed at low exposure times robust, or do they wash away/collapse easily? Resolution/Shape: Does the shape definition change significantly? Identify the exposure time that yields the desired pillar diameter and robustness. Iterate if Necessary: If changing the exposure time significantly alters the required development (e.g., much longer exposure needs slightly longer development), you might need to re-optimize the development time (Step 2) using your new preferred exposure time (Step 3). Usually, one or two iterations are enough. Consider Other Factors (Secondary Optimization): Developer Choice: As shown in JVSTB 2008, switching between AZ-300 MIF and ma-D 331S changes the pillar profile. If your application requires a specific profile (undercut for lift-off vs. vertical for etching), choose the appropriate developer before starting the time optimizations. Post-bake: The Langmuir 2015 paper showed post-baking significantly affected TiO2 pillars. While not explicitly studied for MaN-405 in the JVSTB paper, a post-development bake (hard bake) is common for photoresists to improve mechanical/chemical stability. You could experiment with temperature and time (e.g., 110-150°C for several minutes) after development if pillar robustness is an issue for subsequent processing steps. Resist Thickness: Affects aspect ratio. Thicker resist allows taller pillars but may require longer exposure/development and affect resolution. Simple Experimental Plan: Fix: Resist (MaN-405), Resist Thickness, Sphere Size, UV Source, Developer (e.g., AZ-300 MIF). Variable 1 (Exposure Time): Choose an initial guess (e.g., T_exp = 10s). Variable 2 (Development Time): Run a series (e.g., 20s, 30s, 40s, 50s, 60s, 70s) keeping T_exp constant. Analyze via SEM. Find Optimal T_dev. Variable 1 (Exposure Time): Run a series (e.g., 5s, 8s, 10s, 12s, 15s, 20s) using the Optimal T_dev found above. Analyze via SEM. Find Optimal T_exp for desired size/robustness. (Optional Refinement): Re-check development time around the previously found optimum using the new Optimal T_exp. (Optional Further Step): Investigate effect of post-bake temperature/time if needed. This approach directly uses the findings related to MaN-405 and development time from the key paper, while incorporating the well-established principle (supported by others) that exposure time controls feature size for negative resists in SLPL.