Comparisons to Metalenses
Recently, I came across the concept of BIC. As presented, I wasn't 100% percent sure if the concept naturally carries over to metasurface absorbers. Also I met with metalens researchers looking to build a shared database - and at some point I came across software (with a built-in database) designed to create photomasks, but "marketed" for metalens designers.
Naturally, I felt it was time to address this ignorance and understand the differences more deeply.
I created a socratic dialogue using claude:
'''Export a summary of our conversation for an article (written in Markdown, with LaTeX equations). Frame the summary as a socratic dialogue, perhaps beginning with the philosophical overarching crux of the matter, but gradually building up from simple to more gradually more sophisticated probing question steps. For answers include some basic visual metaphorical explainers to make understanding of any difficult concepts lucid. Assume the target reader is age 14, but the accuracy of the summary is phd level. '''
'''In traditional socratic method the teacher is asking the questions. In a leading way. Leading to the next concept, building on it, or diverting to the next hidden part. I want you to try again one more time, and also, through the dialogue, explain concepts like phase control. Make the summary cover type of losses, hotspots, resonance types, extinction coefficient, surface vs bulk absorption, coherence etc. Use all the correct terminology like Purcell Factor. '''
The two dialogues are here, and below that are my active reading notes to distill the dialogue even further.
Titanium dioxide is a perfect metalens material, because it has very low losses in the visible spectrum.
Multifunctional metasurfaces may soon have the capability to switch between high or low loss; using active materials tuned by a external stimuli.
A Figure of merit that combines transmission, phase coverage, and absorption may quantify a continuum.
High Figure of Merit would indicates lens-like behaviour low would suggest absorber-like behaviour, but the boundary is blurry!
Extinction coefficient (often denoted 'k') is a measure of how quickly light dies out in the material
Phase control refers to our ability to manipulate the phase of light as it passes through different parts of the metalens
Imagine runners on a track and we want them to finish all the same time, we could space them out a different distances according to how fast they are; slower runners go at the front, while faster ones go at the back.
We adjust the phase at different points, so that all the light waves arrive at the focal point in phase.
? Absorption happens at the surface or in the bulk material ?
Ultra-thin absorbers for sensing applications would utilise Surface Absorption,
Bulk Absorption can lead to more complete absorption over a wide range of wavelengths. ?
Hotspots are areas of intense electromagnetic field concentration.
And absorber, this would correspond to areas of high absorption
In metalenses, it would indicate areas of strong light matter interaction
Several different types of resonance might be responsible: SPR, GMR - guided mode resonance, Cavity mode resonance.
Student: What's the fundamental difference between redirecting light and absorbing it?
Teacher: Ah, an excellent starting point! Think of light as a river of energy. A metalens is like a series of carefully placed rocks that guide the river in a specific direction, while an absorber is more like a sponge that soaks up the water. Both interact with the river, but their effects are quite different. In essence, a metalens manipulates the path of light without significantly reducing its energy, while an absorber converts the light's energy into another form, usually heat.
For a metalens: Transmission (T) or Reflection ® > 70%
For an absorber: Absorption (A) > 90%
BIC stands for "Bound States in the Continuum". Imagine a secluded cove in the ocean where water gets trapped even though it's connected to the open sea. That's a bit like what a BIC does with light.
BIC resonances can have very high Q-factors, meaning they trap light very effectively.
This can be useful for both lenses and absorbers, but in different ways:
For lenses, we can use these high-Q resonances to get very precise control over the light's phase.
For absorbers, these resonances can lead to very efficient absorption at specific frequencies.
Student: So if we combine many of these high-Q resonances, does that automatically make it an absorber?
Teacher: Not necessarily! It all depends on how we combine them. If we carefully control how these resonances interact to maintain a specific phase profile across a wide range of colors, we could still have a broadband metalens.
But if we're mainly concerned with achieving high absorption across many colors, without worrying too much about the phase, then yes, we'd be creating a broadband absorber.
Student: That's fascinating! But if they're both made of tiny structures, how do we decide if something is a metalens or an absorber? Teacher: Excellent question! This brings us to the heart of our discussion. The distinction often comes down to the device's primary function and efficiency. Let's consider a few key factors:
Transmission vs. Absorption: A good metalens should let most of the light through (or reflect it, for a reflective lens), while an absorber should, well, absorb most of the light. We can express this mathematically: For a metalens: Transmission (T) or Reflection ® > 70% For an absorber: Absorption (A) > 90% Phase Control: A metalens needs to carefully control the phase of light across its surface. We often look for a full 2π phase coverage. An absorber doesn't necessarily need this level of phase control. Q-factor and Bandwidth: The Q-factor is a measure of how "sharp" a resonance is. High Q-factors can be useful for both lenses and absorbers, but in different ways. A simple way to think about it is:
For a lens, we usually want to minimize energy loss, while for an absorber, we want to maximize it.
Student: This is getting complex! Is there a simple way to tell them apart? Teacher: You're right, it can be complicated! One way to simplify this is to use a Figure of Merit (FOM). We can define this as: Where Φ (Phi) represents the phase coverage. A high FOM suggests the device is behaving more like a lens, while a low FOM suggests it's more like an absorber.
Other truths / questions:
What does surface plasmon resonance Look like in reality?
Mode volume refers to the spatial extent of a resonance, how big or small is the volume of energy confinement?
'Hotspots' would refer to the number density of these regions within a wider area or structure; high mode volume = no hotspots.
Purcell Factor is a measure of how well a structure can enhance light matter interactions; proportional to Q factor divide mode volume.
Coherence is how 'organised' the light waves are, if they are not well-coordinated, they are incoherent.
Collisions with lattice ions cause thermal losses, causing the material to heat up.
While electrons (in motion) jumping to higher energy levels are a store of energy, which is their average distance away from positive ions.
These electronic transition-levels can be considered cavity modes.
Radiative loss is when absorbed energy is remitted as light. Also called Spectral Excitance.
? In metallic nano structures, we often encounter plasmic losses related to the oscillation of electrons mentioned earlier ?
CR occurs when light is trapped in a confined space, leading to standing waves.
GMR happens when light couples to modes that propagate along a layer or interface.
SPR involves the coupling of light to electron oscillations at metal-dielectric interfaces.
All of these can be engineered to enhance absorption in specific spectral ranges.
Absorptivity (k) and Losses: You're correct that absorptivity and losses are closely related. High losses in a material or structure generally correspond to high absorptivity. The extinction coefficient k is directly related to the absorption coefficient α through the relation α = 4πk/λ, where λ is the wavelength.